Potain IGO T130
- Max capacity: 17,637 lb (8,000 kg)
- Max tip capacity: 3,086 lb (1,400 kg)
- Max radius: 164 ft (50 m)
- Max height under hook with jib horizontal: 122 ft (37.3 m)
- Max height under hook with jib at 30°: 200 ft (61 m)
- Variable height lattice mast from 63 ft (19.3 m) to 122 ft (37.3 m) with mast inserts.
Chassis: Outriggers swing and lock into position. 16.4 ft (5 m) square outrigger spread with 13.1 ft (4 m) maximum turning radius. 23.6 in (600 mm) square outrigger pads are stowed on the crane during transport.
Ballast: Ballast requirement for the crane consists of, at minimum, eleven (11) slabs each weighing 8,929 lb (4,050 kg). An additional slab is required in some raised jib configurations.
Mast: Telescoping lattice mast is raised by an auxiliary winch and pulley block. Hook heights of 63 ft (19.3 m) and 73 ft (22.3 m) are achievable with the standard mast. 360˚ rotation possible during raising sequence.
Mast Inserts: Three (3) 20 ft (6 m) mast inserts available to reach a maximum horizontal hook height of 122 ft (37.3 m).
Increasing mast height with one insert provides hook heights of 83 ft (25.3 m) and 93 ft (28.3 m); second mast insert provides hook heights of 103 ft (31.3 m) and 113 ft (34.3 m); third mast insert provides a hook height of 122 ft (37.3 m).
Jib: 164 ft (50 m) radius standard offsettable lattice jib. The jib can be offset to 30˚. Opening and aligning are carried out automatically by four hydraulic cylinders.
Swing: RVF 161 Optima+ slewing mechanism with a maximum swing speed of 0.8 rpm. Progressive control of the speed with counter-slewing possible, anti-load swinging system makes aligning the load and jib easier. Multiple rpm speeds possible depending upon parameter selected.
Hoist: 33 LVF 20 Optima: 29.5 HP variable frequency hoist with 4,400 lb (2 t) line pull. Progressive speed change according to the accelerating or decelerating ramps. Optima allows the hoist to adapt its speed to the weight of the load.
Trolley: 5 DVF 5: 5.4 HP variable frequency hoist with 1,102 lb (500 kg) line pull. Progressive speed change according to acceleration or deceleration ramps controlled by the frequency converter.
Reeving: SM/DM block for 2 (SM) or 4-part line (DM). Manual removal of one pin to change between SM and DM.
480 volt and 60 Hz measured at the turntable are recommended for optimal performance. Power Control allows for a reduction in power supply of 35 kVA to 19 kVA from city and 60 kVA to 35 kVA from a generator, with a proportional reduction in hoisting speed. Earth rod and electric cable stored on the crane during transport.
The wireless remote control provides information to the operator about wind speed, radius, hook height, load, and moment. Lights and buzzers alert the operator when nearing limits of operation. Battery charger and extra battery are provided with the crane.
Auxiliary push-button tethered remote ensures continual operation in case of battery or other malfunction of the wireless remote control. Optional tethered remote control ensures continuous operation with the same functions and ergonomics as the standard wireless remote control.
Optional transport axle sets are available for both jobsite and highway applications. Jobsite axles are rated for 15.5 mph (25 km/h) and highway axles are rated for 50 mph (80 km/h).